As a remote controller for the Sumo robot (see “Zumo Robot with Magnetic Encoders“) we have used so far a combination of NXP FRDM-KL25Z board and a Joystick Shield (see “Joystick Shield with nRF24L01 driving a Zumo Robot“). That solution was not ideal, so this weekend I created a 3D printed prototype:
tinyK20 Remote Controller
We are using robots to teach advanced embedded system programming at the Lucerne University (see “Sumo Robot Competition“). Students can buy the kit, and we are running out of available hardware. Time to produce a new series of robots :-). It took us a while to get to the next revision of the Zumo Robot, but finally the first one has been produced and assembled, and I think it is looking good :-).
Intro_Zumo_Robot
It has been extremely busy weeks, and I’m my technical blog article output currently is very low. So I thought I could post two pictures of blooming Crocus in my backyard instead. I admit: that takes less time than writing up a 2000 words geeky technology article. And I know that some of you might say “Flower pictures do not count!”. But hey, I say that the Crocus is a very beautiful flower, and in many aspects nature is ahead of technology:
Crocus
I’m using the tiny and inexpensive Nordic Semiconductor nRF24L01+ transceiver (see “Tutorial: Nordic Semiconductor nRF24L01+ with the Freescale FRDM-K64F Board“) in many projects: it costs less than $3 and allows me to communicate with a proprietary 2.4GHz protocol in a low power way (see “IoT: FreeRTOS Down to the Micro Amps“). I have that transceiver now running with the tinyK20 board too:
nRF24L01+ Transceiver with tinyK20
I’m using the FRDM-KL25Z in my classes, and that board is very popular: low price (<$15), reasonable features (48 MHz ARM Cortex M0+, 128 KByte of FLASH, 16 KByte of RAM), and many tutorials elsewhere and on McuOnEclipse :-).
For the next (Fall) semester I’m looking for alternative boards, and one is the Freescale (now NXP) FRDM-KL27Z:
FRDM-KL27Z with Box
In case you are running into this problem that launching GDB hangs with this message in Eclipse:
Launching Configuring GDB Aborting configuring GDB
I’m exploring the Kinetis SDK v2.0 (see “First NXP Kinetis SDK Release: SDK V2.0 with Online On-Demand Package Builder“). For this, I’m using the ‘standard’ way: blinking the LED on the board 🙂
Blinky on FRDM-K64F Board
If using a bootloader with an application, one thing is to to merge the bootloader with the application into a single file. I do this with the ‘SRecord’ tool like this:
srec_cat bootloader.s19 application.s19 -o merged.s19
Combining S19 Files
So far, the XML files I had to work on were very simple ones, so a normal text editor was fine. Now I’m tapping into the world of CMSIS-Packs (see “Are ARM CMSIS-Pack the Future of Software Components?“). And definitely this adds a complexity for which I better use some XML editing and checking tools. The ARM tutorial for CMSIS recommends either Notepad++ or Visual C++. But hey, Eclipse should be able to do that maybe even better right? So this is about adding an XML editor and XML checker to Eclipse.
Editing CMSIS-Pack .pdsc File in Eclipse
It has been a cold night with snowfall mostly in the higher mountains. For a very short time window opened up in the sky for the raising sun:
Winter Sunrise Reflections
It created nice reflections the water and ice on the ground: like fire on ice.
The following panorama picture is taken near the same spot as above in the “Sägel” nature preservation area, towards the Mythen peaks in the East:
MCU on Eclipse 