Tag Archives: software project

Hacking the Heating System for Cooling – Geothermal Drilling with extra Benefits

Posted on by
38

Summer finally has arrived in Switzerland. Yes, I live in a moderate climate zone, but if the outside temperature goes above 28-30° Celsius as these days, then sleeping at night is not that comfortable as it should be in my view. Luckily, I’m in a good constructed house with good insulation, so it takes a few days until it heats up. But I love to keep the temperature below 25° Celsius, especially at night. I do have a heating system which combines geothermal and solar heating. The question is: how can I use it for cooling during hot summer days? The solution: some extra plumbing, a Freescale Tower system and the Freescale FRDM-KL25Z board 🙂

FRDM-KL25Z with Arduino Data Logger Shield

FRDM-KL25Z with Arduino Data Logger Shield controlling Heating/Cooling System

Continue reading →

FRDM-KL25Z talks to Android Phone

Posted on by
3

Ok, I still do not own an Android phone, but I know many readers of this blog do, and there were several questions how to use the FRDM-KL25Z with Android. And here is something exciting I just saw today: Kai Liu posted information how to connect the FRDM-KL25Z with USB OTG (On-The-Go) to Android: FRDM-KL25Z now talks to Android Phone

He published the S19 file so you can try things out. He still needs to organize the sources and decide on how to publish it (I hope it will be available soon).

If you do not own a FRDM-KL25Z RevE, then you need to consider this post about a hardware change: USB host HID demo times out on FRDM-KL25Z with reproduced USB host

Happy Droiding 🙂

USB MSD Host for the FRDM-K20D50M Board

Posted on by
63

The Freedom boards FRDM-KL25Z RevE and FRDM-K20D50M make it easier to use it as USB Host device, as they come with a special jumper to provide 5V to the USB device, so my earlier ‘hack’ is not needed any more :-). After I had USB MSD Host working for the FRDM-KL25Z, it was much harder to get the USB stack working for the FRDM-K20D50M board, because somehow the example Freescale provided with their USB stack refused to work properly on my board. After debugging it for several nightly hours, I decided to take my working Processor Expert project for KL25Z and added support for the K20. And the good news is: since tonight this is working :-).

FRDM-K20D50M as USB MSD Host

FRDM-K20D50M as USB MSD Host

Continue reading →

FreeRTOS Heap with Segmented Kinetis K SRAM

Posted on by
56

While working on a project for the FRDM-K20D50M, I faced a problem: I was running out of SRAM for my application. The GNU linker reports: “section `.bss’ will not fit in region `m_data'”: 😦

bss will not fit in region m_data

bss will not fit in region m_data

But my device has 16 KByte of SRAM, and I knew I use much less than 10 KByte. So what is the problem? Continue reading →

Yet another Bluetooth Firmware: BC04

Posted on by
12

I was thinking that these common and cheap bluetooth modules have either HC-05 or HC-06 firmware (see this post). Well, I was wrong: there are more! Obviously there many more firmware images available on that British CSR BlueCore4-Ext chip. Mihai Surdeanu contacted me with an updated firmware for a module which has the “BC04” firmware on it. He was so gentle and has sent me an updated Processor Expert component which works with that BC04 firmware :-).

Continue reading →

Using the FRDM-KL25Z as USB Keyboard

Posted on by
106

I miss my old DELL laptop. Ok, the new one I received from IT services is not bad. It is faster and has a better screen. But I’m not really happy with the new keyboard. With the previous keyboard I was able to do a ‘PrtnScrn’ with a single key press. With the new one I need to press Fn + PrntScrn. And this is impossible to do with one hand:

Impossible to reach Prnt Scrn

Impossible to reach Fn+Prnt Scrn with one hand!

Yes, I have two hands ;-). But many times I need to do ‘print screen’ while having my other hand on the mouse :-(.What else can I do?

Continue reading →

Using the HC-06 Bluetooth Module

Posted on by
177

After my first post using a Bluetooth module, things have evolved a bit. The challenge with these Bluetooth modules is: they look the same, but having different firmware. I did not fully realize that until I have ordered another bluetooth module from dx.com:

DX.com Bluetooth Module (HC-06)

DX.com Bluetooth Module (HC-06)

That module comes already on a carrier, so I assumed I can use the same driver as for my other module. I was wrong :-(.

Continue reading →

Traps and Pitfalls: No Hex/Bin/S19 File Created with GNU?

Posted on by
12

I stumbled now twice over a problem, and only after a lot of head scratching (you should see my head now 😉 ) I have found the cause (and solution) for it. In the hope that I can save the readers of this blog some time, here is what happened.

I described in earlier posts how to enable GNU build tools to generate hex/bin/S19 files, or to write the code size to the console view. That works fine for me. But then I received a project were obviously this does not work: even with the project settings configured properly, there is no S19 file, and no code size printed. What’s wrong?

Additional Tools in ARM GNU Eclipse Panel

Additional Tools in ARM GNU Eclipse Panel

Continue reading →

Tutorial: Arduino Motor/Stepper/Servo Shield – Part 2: Timed Servo Moves

Posted on by
6

You have decided: More than 52% voted in Part 1 that the next topic should be Timed Servo Moves. So here we go :-).

This is about how to move the servos over time, instead of moving it to the given position as fast as possible. I’m using a linear approach here: moving the servos linearly over time.

Moving Servo Motors

Moving Servo Motors

Continue reading →

Tutorial: Arduino Motor/Stepper/Servo Shield – Part 1: Servos

Posted on by
28

This post starts a small (or larger?) series of tutorials using the Arduino Motor/Stepper/Servo Shield with the FRDM-KL25Z board. That motor shield is probably one of the most versatile on the market, and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project :-).

Arduino Motor Stepper Servo Shield with FRDM-KL25Z

Arduino Motor Stepper Servo Shield with FRDM-KL25Z

Continue reading →